Hempel Thinner 845 0,75 Lt 456COL036
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
MORE INFORMATION
HEMPEL THINNER 845
The paints HEMPEL produced and supplied in such a way that thinning is normally not necessary provided the paint is properly mixed/stirred prior to use.
However, if the paint is to be applied in a low film thickness (for instance as a "sealer coat") or if the paint has become too thick, e.g. in cold weather, the HEMPEL THINNER(s) indicated on the product data sheet may be added to obtain a consistency most suitable for application. As a general rule, thinning should be kept at a minimum as the quality of the paint work will suffer from too much thinning. However, if application is to take place at high temperatures (air and/or steel), thinning may even beyond the limits mentioned on the data sheets may be necessary in order to avoid dry-spray and poor film formation.
The THINNERS aare blended to give the best results with regard to brush ability, spray properties, etc. In some cases ordinary solvents may substitute. As such products are beyond our control, we disclaim any responsibility for the results. In each case the respective product data sheet should be consulted.
Regarding the use of THINNERS for cleaning, kindly refer to the NOTES.
Type of thinner: 08080
Flash point: 25 ° C
Examples of products which can be diluted with the corresponding thinner:
HEMPEL'S ANTIFOULING GLOBIC NCT & SAP, OCEANIC,
OLYMPIC
HEMPALIN DECKPAINT 53240
Series products HEMPAQUICK
Series products HEMPATEX (acrylic)
Glazes and finishes the series
HEMPATHANE (polyurethane)
Type of thinner: 08230
Flash point: 32 ° C
Examples of products which can be diluted with the corresponding thinner:
Products series HEMPALIN except HEMPALIN
DECKPAINT 53240, series products and HEMPAQUICK
other alkyd generally
Type of thinner: 08450
Flash point: 23 ° C
Examples of products which can be diluted with the corresponding thinner:
Series products HEMPADUR (epoxy)
Type of thinner: 08510
Flash point: 3 ° C
Examples of products which can be diluted with the corresponding thinner:
Special thinner for HEMPATHANE ENAMEL 55100
HEMPATHANE ENAMEL 55210
HIGHLY FLAMMABLE
Type of thinner: 08570
Flash point: 4 ° C
Examples of products which can be diluted with the corresponding thinner:
HEMPEL'S SHOPPRIMER E 15280
HEMPEL'S SHOPPRIMER ZS 15890
Type of thinner: 08700
Flash point: 24 ° C
Examples of products which can be diluted with the corresponding thinner:
HEMPEL'S GALVOSIL Series and products
series HEMPADUR be applied as a sealant
Anti-popping on GALVOSIL
NOTES:
THINNER HEMPEL'S THINNER 845 has greater thinning properties than alcohol and turpentine.
The equipment is usually cleaned with the same thinner used for the products applied.
For cleaning tools used for products of the HEMPADUR series, the use of HEMPEL'S TOOL CLEANER 99610 is recommended.
This product should not be used as a thinner and should not be used for cleaning tools used for the application of the products of the HEMPATHANE series.
NOTE:
HEMPEL'S THINNER 845 is for professional use only.
