International Ultra 300 Antfouling 0,75Lt Light Blue YBB702 N702458COL629
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
International Antifouling Ultra 300 0.75Lt Light Blue YBB702
Offers protection in the highest fouling conditions where a hard, scrubbable antifouling is required. Ideal for fast powerboats.
* High strength, hard antifouling
* Hard, scrubbable finish to allow clean-off if needed
* Suitable for burnishing to provide a smooth finish
* Smooth finish for maximum slip through the water
* Contains Biolux® technology for sustained antifouling protection
PRODUCT INFORMATION:
Finish: Matt
Specific Gravity: 1.5
Volume Solids: 45% average
Typical Shelf Life: 2 yrs
VOC (As Supplied): 485 g/lt
Unit Size: 750 ml
DRYING/OVERCOATING INFORMATION
Drying:
5°C (41°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Touch Dry: 1 hrs 45 mins 30 mins 20 mins
Immersion 24 hrs 12 hrs 8 hrs 6 hrs
Note: Max. Immersion Times are as follows: 5-15°C - 3 mths; 23°C - 2 mths; 35°C - 1 mth Overcoating:
Substrate Temperature
5°C (41°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Overcoated By Min Max Min Max Min Max Min Max
Interspeed Ultra 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext
Micron 66 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext
Micron Extra (Professional) 16 hrs ext 10 hrs ext 6 hrs ext 4 hrs ext
APPLICATION AND USE:
Preparation: PREVIOUSLY ANTIFOULED SURFACE:
In Good Condition: Rinse with fresh water and allow to dry. If old antifouling is incompatible or unknown, seal with Primocon.
In Poor Condition: Use Interstrip to remove all traces of antifouling.
PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP: Gelshield 200 for osmosis protection, or Primocon.
STEEL/IRON: Prime with Interprotect or Primocon.
LEAD: Prime with Interprotect or Primocon.
WOOD: Prime with Interprotect or Primocon.
Method: Apply two coats per season.
Useful tips: Mixing Stir well before use.
Thinner: YTA085 Thinners No.3
Thinning is not recommended.
Cleaner: YTA085 Thinners No.3
Other: True colour will develop after immersion. Take care to apply all the paint calculated even if it means applying an extra coat. It is important for performance to apply the correct thickness.
Some Important Points: To prevent poor results, ensure the correct amount of paint is applied using the coverage as a guide. Product temperature should be minimum -5°C and maximum 35°C. Ambient temperature should be minimum -5°C and maximum 35°C. Substrate temperature should be minimum 1°C above dew point and maximum 35°C.
Compatibility/Substrates: GRP, Wood, Steel/Iron, Lead. Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces. Can be applied direct over most types of antifoulings, provided they are in sound condition
Number of Coats 2-3 by brush/roller
Coverage (Theoretical) - 10.5 m²/lt by brush
(Practical) - 9.4 m²/lt by brush
Recommended DFT per coat 43 microns dry
Recommended WFT per coat 96 microns wet
Application Methods: Brush, Roller, AIRLESS SPRAY NOT
Unit size 0.75 lt.
Light Blue colour YBB702.