Boero Polywood Two-component Wood Preserver 1 Lt 000 Transparent 45100530
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Boero Polywood Two-component Wood Preserver. 1 Lt. 000 Transparent.
It is a two-component transparent sealer used for impregnating high-quality woods, marine polywoods and MDF panels. It penetratse and isolates and produces surfaces that are easy to sand and to be covered with mono or two-component products for achieving either coloured or clear surfaces. This product is mainly used on new wood or wood that has been completely sanded down. It must absolutely not create a layer on the surface but it has to penetrate inside the surface.
PHYSICAL ASPECT (at 20° C)
Finish: Glossy
Colour: Colourless
Solids (by volume): 50 ± 2 %
Specific gravity: 0,92 ÷ 0,96 g/cm³
Flash point: < 21° C
Viscosity: 90 ÷ 95" F4 a 20° C
APPLICATION DETAILS
Mixing ratio (by volume): 1:1
Pot life: 5hr depending on termperature
Thinner: Temp. < 18° C – 696.000 Temp. > 18° C – 697.000
Spray viscosity: 14” – 16” DIN 4 a 20° C
Application Method
Conventional: Nozzle: 1,4 mm Pressure: 3,5 bar
Mixed air: Nozzle: 0,7 mm – 1 mm Nozzle: 3,5 bar
Thinner: 697 (5 – 10 %)
Dry film thickness: Standard range of application 30 μ (Recommended 30 μ)
Wet film thickness: Standard range of application 60 μ (Recommended 60 μ)
Theoretical coverage m2/litro: Range of application at recommended thickness 17
Note: The product is provided in two tins to be mixed entirely and carefully before use. The eventual dilution must be done after mixing the two components together. The physical data of two-component products refer to the components after they have been mixed together.
SURFACE PREPARATION
New wood: Apply directly on clean wood.
Old wood: Complete removal of old painting cycle with paint stripper, flame, scraper or sanding. Clean and dust.
Painting cycles
New wood: Apply a coat of Polywood diluted by 10 - 20% and after 1-2 hours apply a second coat. After 6-8 hours proceed with sanding and subsequent application of one or two-component cycle.
Bare old wood: Apply a coat of Polywood diluted by 10 - 20%. After 6-8 hrs proceed with sanding of the support with subsequent application of one or two-component cycle.
APPLICATION CONDITIONS
Per evitare il formarsi di condensa, la temperatura del supporto deve essere superiore al punto di To avoid the formation of condensation, the temperature of the surface should be at least 3 °C above dew point. During the application and curing the min. ambient temperature should be 15 °C, or higher than 30° C; substrate temperature must not be lower than 10° C since curing is reduced at lower temperatures. Application is not advisable when relative humidity exceeds 80%. The thermo-hygrometric survey should be carried out near the surface to be coated. It is important to be sure there is sufficient ventilation when the application takes place in closed areas.
SAFETY RULES
In order to protect personal health it is advisable to comply with the EU DPR 303 and 547 regulations. Avoid, for example any contact of the product with the skin and eyes. Use in well ventilated areas,in enclosed areas use aspirators, fans and air ventilators. Wear masks, goggles, gloves while applying the product.
NOTE
Ensure that the product does not come in contact with water, chemical products or undergoes mechanical stress before the curing is complete. The wet film thickness is referring to an undiluted product. In case of dilution, this value increases.
