Boero Epoply Undercoat Epoxy Filler 2,5 Lt A+B 001 White 45100401
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Boero Epoply Undercoat Epoxy Filler. 2,5 Lt. A+B. 001 White.
Undercoat epoxy filler for use in two-component cycles of topsides. Excellent compact film thanks to excellent flow; easy to sand and provides a perfect surface finish.
PHYSICAL ASPECTS
Aspect: Matt
Colour: White .001
Volume solid % : 50 ± 2 %
Specific Weight: 1,36 ÷ 1.40 g/cm³
Flash Point: 28° C
Viscosity: thixotropic (15.000 ÷ 18.000 cP)
APPLICATION DETAILS
Mixing ratio by volume: 4:1 with 651.000
Pot Life: 8h at 20° C
Thinner: 693.000 (max. 15%)
Applications
Conventional: Pressure: 3,5 bar Nozzle diameter: 1,5 – 1,7 mm
Mix air: Pressure: 3,5 bar Nozzle diameter: 1,2 mm – 1,5 mm
Thinner: 693.000 (max. 5%) (only for small areas)
Dry film thickness: Standard range of application 75 μ - 150 μ (Recommended 100 μ)
Wet film thickness: Standard range of application 150 μ - 300 μ (Recommended 200 μ)
Theoretical coverage m2/litre: Range of application at recommended thickness 5
Recommended primers: Delta 3000 - Epomar - Delta UC HB
Note: The product is provided in two tins to be mixed entirely and carefully before usage. The eventual dilution must be done after mixing the two components. The physical data of two-component products refer to the components after they have been mixed together
SURFACE PREPARATION
Wash with high pressure fresh water to remove every trace of oil and grease. All surfaces should be clean, dry and without contaminations. Sand with paper 180 grit, vacuum to remove all residue of sanding and any dust or dirt. Subsequently blow with clean dry air.
Fiberglass: On new surfaces degrease with SIRIO before sanding with paper 240/320 grit, vacuum to remove sanding residue and any dust or dirt. Subsequently blow with clean dry air.
CONDITIONS DURING APPLICATION
To avoid the formation of condensation, the temperature of the surface should be at least 3° above dew point. During the application and curing, the min. room temperature must not be lower than 10°C or higher than 30° C; substrate temperature must not be lower than 5° C, since curing is remarkably reduced at lower temperatures. Application is not advisable when relative humidity exceeds 80%. The thermo-hygrometric survey should be carried out near the surface to be coated. Make sure there is enough ventilation when the application takes place in closed areas.
SAFETY RULES
In order to protect personal health it is advisable to comply with the EU DPR 303 and 547 regulations. Avoid, for example any contact of the product with the skin and eyes. Use in well ventilated areas, in enclosed areas use aspirators, fans and air ventilators. Wear masks, goggles, gloves while applying the product.
NOTE
The applied product must not come in contact with water, chemical products or submitted to mechanical stress before the curing is completed. The wet film thickness refers to an undiluted product. In case of dilution, this value increases.
