International Ultra 300 Antifouling Lt 2,5 Dover White YBB728 458COL640
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Ultra 300 is an antifouling product effective against fouling organisms; slime, aquatic plants and animals. A Premium Hard Antifouling suitable for professional and consumer application onto vessels in fresh and salt water. The hard scrubbable finish provides protection for up to one year performance. Ultra 300 is suitable for burnishing to provide a smoother finish for maximum slip through the water and can be scrubbed and cleaned if needed. Ideal for fast Powerboats.
PRODUCT INFORMATION
Colour: YBB728 White Dover
Finish: Matt
Specific Gravity: 1.9 average
Volume Solids: 58% average
Typical Shelf: Life 2 yrs
VOC (As Supplied): 364g/l average
VOC (EU Solvent): 197g/Kg average EU Solvent Emissions Directive (Council Directive 1999/13/EC)
Unit Size: 2.5 Lt
APPLICATION AND USE
Preparation
PREVIOUSLY ANTIFOULED SURFACE
In Good Condition: All fouling and contamination must be thoroughly removed including the leached layer. Use high pressure fresh water wash (3000 psi/207 bar) and/or scraping and wet sanding with typically 80120 grade paper. Do not dry sand. If old antifouling is incompatible or unknown, seal with suitable International Paint barrier/sealer coat.
In Poor Condition: Use Interstrip to remove all traces of antifouling.
PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP: Prime with Gelshield 200 for osmosis protection, or Primocon or Interprotect.
STEEL/IRON/LEAD/WOOD: Prime with Interprotect or Primocon.
Advice
Mixing: Thoroughly stir until product is mixed to a uniform consistency before use
Thinning: Thinning is not recommended. Antifouling performance can be compromised if correct dry film thickness is not
applied.
Cleaner: YTA085 Thinner No.3
Airless Spray: Pressure: 176210 bar/25003050 psi. Tip size: 517 to 521.
Ventilation and Humidity Control: Ensure adequate ventilation during use.
Other: Antifoulings should only be wet sanded. Never dry sand or burnoff
old antifoulings. True colour will develop after immersion.
Some Important Points
To prevent premature failure, ensure the correct amount of paint is applied using the coverage as a guide. Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be 3°C/5°F above dew point and maximum 35°C/95°F.
Compatibility/Substrates
For use over suitably primed GRP, Wood, Steel/Iron and lead.
Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces.
Can be applied direct over most types of antifoulings, provided they are in sound condition, with the exception of VC17m/PTFE antifoulings. Consult your local International Paint representative for specific overcoating advice if you are unsure about compatibility of Ultra 300 over your existing coating scheme.
The recommended thinner is No.3 Thinner, our code COL652. Unit size 2,5 lt. Colour: White Dover YBB728.
