International Cruiser 250 Antifouling 0,75 Lt Blue YBP152 458COL1011
zoom_out_map
chevron_left chevron_right
-49.03%

International Cruiser 250 Antifouling 0,75 Lt Blue YBP152 458COL1011

Cruiser 250 is a polishing antifouling providing quality year-long protection. Quick-drying and convenient, it can also help you get back on the water sooner.

€44.90 VAT included

€36.80 VAT excluded

€88.08-49.03%

Il Nostro Negozio

Visit us in our shop

WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!

In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!

We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.

Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy

Politiche per la sicurezza
(modificale nel modulo Rassicurazioni cliente)
Politiche per le spedizioni
(modificale nel modulo Rassicurazioni cliente)
Politiche per i resi
(modificale nel modulo Rassicurazioni cliente)

International Antifouling Cruiser 250 0,75 Lt Blue YBP152

Cruiser 250 is a polishing antifouling providing quality year-long protection. Quick-drying and convenient, it can also help you get back on the water sooner.

PRODUCT INFORMATION
Colour Blue YBP152
Finish Matt
Specific Gravity 1.8 average
Volume Solids 60%
Typical Shelf Life 2 yrs
VOC (As Supplied) 353 g/L average
VOC (EU Solvent) 193 g/Kg average EU Solvent Emissions Directive (Council Directive 1999/13/EC)

APPLICATION AND USE
PREVIOUSLY PAINTED SURFACE:
In Good Condition: All fouling and contamination must be thoroughly removed including the leached layer. Use high pressure fresh water wash (3000 psi/207 bar) and/or scraping and wet sanding with typically 80120 grade paper. Do not dry sand. If old antifouling is incompatible or unknown, seal with suitable International Paint barrier/sealer coat.
In Poor Condition: Use Interstrip to remove all traces of antifouling.
PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP: Prime with Gelshield 200 for osmosis protection, or Primocon or Interprotect.
STEEL/IRON/LEAD/WOOD: Prime with Interprotect or Primocon.
PLYWOOD: Prime with Epiglass followed by Interprotect.
Useful tips
Mixing: Thoroughly stir until product is mixed to a uniform consistency before use.
Thinning: Thinning is not recommended. Antifouling performance can be compromised if correct dry film thickness is not applied.
Cleaner: YTA085 International Antifouling Thinner #3.
Ventilation and Humidity Control: Ensure adequate ventilation during use.
Other: Antifoulings should only be wet sanded. Never dry sand or burnoff old antifouling. True colour will develop after immersion.
Some Important
Points To prevent premature failure, ensure the correct amount of paint is applied using the coverage as a guide. Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and
maximum 35°C/95°F. Substrate temperature should be 3°C/5°F above dew point and maximum 35°C/95°F.
If you are regularly travelling at high speed (eg 30 knots) you might experience early wear through. Consult your local International Paint Representative for further advice if you are unsure about the suitability of Cruiser 250 for your specific requirements.
Compatibility/Substrates
Suitable for use on GRP, wood, steel/iron and lead. Not suitable for use over Aluminium/Alloy substrates or zinc sprayedsurfaces.
Can be applied direct over most types of antifoulings, provided they are in sound condition, with the exception of VC17m/PTFE antifoulings. Consult your local International Paint representative for specific overcoating advice if you are unsure about compatibility of Cruiser 250 over your existing coating scheme.
Number of Coats By Brush/Roller:
Apply 2 coats of 60 microns dry for 12 months (Total DFT of 120 microns).

Manufacturer's recommended minimum and maximum prior to immersion in relation to atmospheric temperature:
Atmospheric temperature 5° C-min/max 7 hours/3 months.
Atmospheric temperature 15° C-min/max 5 hrs/3 months.
Atmospheric temperature 23° C-min/max 2 hours/2 months.
Atmospheric temperature 35° C-min/max 2 hours/1 month.


Unit size 750 ml.

458COL1011
8025223421441
16 other products in the same category: