Veneziani Cupron 3.0 2.5L Black .708 Ablative Antifouling N709473COL408
Veneziani Cupron 3.0 ablative antifouling for seasonal protection of Aluminum, Iron, Wood, Fiberglass, 2.5L, 6369.708 Black.
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Veneziani Cupron 3.0 2.5L Black Ablative Antifouling 6369.708
Ablative antifouling that is the result of a formulistic evolution guaranteeing an adequate seasonal protection and a universal application on every type of vessel and support. In order to guarantee a good performance for the season, it is necessary to apply 2 coats of product. This antifouling is compatible with most undercoats such as Ticoprene and Unikote Pro. All colour are suitable for aluminium hulls.
TECHNICAL SPECIFICATIONS
Colour: Black 6369.708
Theoretical coverage: 8 mq/liter
Antifouling support: Aluminium, Iron, Wood, Fiberglass
Antifouling type: Self-polishing
Antifouling use: Hull
Pack: 2.5 lt
APPLICATION
Application: roller, brush
Coverage: approximately 8 m2/litre
Thinner: 6470
Compatible with Adherpox, Ticoprene primer
SURFACE PREPARATION
Surfaces with old antifouling
Good conditions: remove contaminants and any vegetation by high-pressure washing with fresh water. Wet sand with 120-180 grit paper. If the old antifouling is unknown, apply a coat of Ticoprene type sealer. Poor conditions: remove contaminants, any vegetation and loose material by high-pressure washing with fresh water. Wet sand with 80-120 grit paper or lightly sand, taking care not to damage the cycle underneath the old antifouling. Apply a coat of ADHERPOX or TICOPRENE primer over the entire treated area before applying the antifouling.
New or refurbished surfaces
Fiberglass: Degrease the surface to be treated with solvent or a suitable detergent. Pressure wash with fresh water and remove all traces of oil and grease. All surfaces to be painted must be clean, dry and free of contaminants. Sand with sandpaper no. P180 – P220 and prime the treated surface. Before applying the products, blow with clean, dry air to remove any sanding residue and dirt.
Steel: Pressure wash with fresh water and remove all traces of oil and grease (if necessary, wash with a specific solvent). All surfaces to be painted must be clean, dry and free of contaminants. Perform a sandblasting treatment to grade Sa 2½ or, after consulting our technicians, mechanical cleaning to grade St 3. Cover the treated metal with the primer before it shows signs of oxidation. Before applying the products, blow with clean, dry air to remove any sanding residue and dirt.
Aluminum: Clean the surface as for steel. Sand with coarse-grained discs P36 -40. The metal must be silver-colored, completely free from oxidation residues and covered with the appropriate primer on the same day as the preparation described above. Be careful not to polish the surface without, however, overdoing the engraving. Before applying the products, blow with clean, dry air to remove any sanding residues and dirt.
New wood: the humidity level of the substrate must not exceed 18%. All surfaces to be painted must be clean, dry and free from contaminants. Sand with paper no. P80 - P120. Before applying the products, blow with clean, dry air to remove any sanding residues and dirt.
Lead: Pressure wash with fresh water and remove any traces of oil and grease (if necessary, wash with a specific solvent). All surfaces to be painted must be clean, dry and free from contaminants. Sand with coarse-grained discs (mechanical cleaning) the surface layer of the metal must be renewed completely and uniformly, removing any oxidation residue and covered with the primer provided on the same day of preparation. Be careful not to overdo the engraving. Before applying the products provided, blow with clean and dry air to remove any sanding residue and dirt.
