Veneziani WOOD V-SHINE AQUA 7W6.312 2.5L SC water-based gloss varnish YM473COL522
Veneziani WOOD V-SHINE AQUA 7W6.312 Single-component water-based gloss varnish stands out for its excellent elasticity and spreadability, .000 Colourless, 2.5L.
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Veneziani WOOD V-SHINE AQUA 7W6.312 Single-component water-based gloss varnish
Shiny single-component alkyd water-based varnish with high surface hardness and outdoor resistance. No blocking effect. Offering excellent coverage, it stands out for its excellent elasticity and spreadability. Odourless.
Application: brush or roller.
TECHNICAL SPECIFICATIONS
Theoretical coverage: 10,0 m2L
Recoating time: 24h - 7days (20°C)
Hard dry: 24h
Thinner: water
Finish: Glossy
Colour: Colourless .000
Solids (by volume): ASTM D2369 30 ± 2%
Specific gravity: UNI EN ISO 2811-1 1,30 ± 0,05 g/cm³
Flash point: UNI EN ISO 13736 N.A.
VOC (calculated average content): ISO 11890-2/2006 130 g/l
Pack: 2.5 Lt
SURFACE PREPARATION
New or renewed wood: The substrate must be dry, the humidity of the wood must not exceed 18%. All surfaces to be painted must be clean, dry and free from contaminants.
Apply on the recommended primers, sand with P220-P320 paper. Before proceeding with the application of the products provided, blow with clean and dry air to remove any residual sanding and dirt. Apply the first coats of V-SHINE AQUA diluted 10 - 15%. Proceed with the
following coats (3 - 5 coats) as it is.
Already painted wood: sand to eliminate traces of paint during stripping or to level the surface; apply the first coats of V-SHINE AQUA diluted at 5%, proceed with the following coats (2 - 4 coats) as it is.
N.B. Between coats, sand with fine Scotch Brite (gray).
CONDITIONS DURING APPLICATION
In order to avoid the formation of condensation, the temperature of the surface should be at least 3 °C above dew point. During the application and curing the min. ambient temperature must not be lower than 15 °C or higher than 30 °C; the min support temperature must not be
lower than 10°C, because the crosslinking is significantly slowed at temperatures below.
Application is not advisable when relative humidity exceeds 80%. The term-hygrometric survey should be carried out near the surface to be coated. Make sure there is enough ventilation when the application takes place in closed areas.
Storage
It is recommended to avoid exposure to air and extreme temperatures. To maximize the shelf life in the can, it is good to check that the container is well closed during the storage and the temperature is between 10 °C and 35 °C. Avoid exposure to direct sunlight.
