Veneziani Gummipaint Enamel 0,5 Lt Orange 473COL1192
zoom_out_map
chevron_left chevron_right
-15%

Veneziani Gummipaint Enamel 0,5 Lt Orange 473COL1192

This product is suitable for painting surfaces in neoprene, rubber fabric, PVC, etc. Moreover, it has excellent levelling and flexibility properties, as well as good adherence.

€54.54 VAT included

€44.70 VAT excluded

€64.16-15%

Il Nostro Negozio

Visit us in our shop

WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!

In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!

We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.

Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy

Politiche per la sicurezza
(modificale nel modulo Rassicurazioni cliente)
Politiche per le spedizioni
(modificale nel modulo Rassicurazioni cliente)
Politiche per i resi
(modificale nel modulo Rassicurazioni cliente)

Veneziani Gummipaint enamel 0,5Lt Orange

This product is suitable for painting surfaces in neoprene, rubber fabric, PVC, etc. Moreover, it has excellent levelling and flexibility properties, as well as good adherence. High resistance to marine environments, immersion in fresh and salt water and ultraviolet rays.

Product information
Finish Semi-gloss
Solids (by volume) ASTM D2369          15 ± 2%
Specific gravity UNI EN ISO 2811-1     1,00 ± 1,05 g/cm³
Flash point UNI EN ISO 13736           > 24 °C
VOC (average calculated content) ISO 11890-2/2006    668 g/l
Packaging 0,5 Lt

Application and use
SURFACE PREPARATION
Degrease the surface to be treated with an adequate solvent or detergent. Pressure wash with fresh water and remove any trace of oil and grease. All surfaces to be painted must be clean, dry and with no contaminants. Sandpaper with P150 – P180 abrasive paper and apply the primer on the treated surface. Before applying the required products, blow with clean and dry air to remove any sanding or dirt residual.
Thoroughly mix the product before use. This product is suitable both for brush and spray application
By brush: a dilution level between 5-10% by volume with thinner 6380 is required.
Given that this is a fast drying product, our advice is to avoid crossing the coats, because this can soften the coat that has been already applied.
By spray: a dilution level between 30-50% by volume with thinner 6380 is required, following the instructions on the back of the sheet. With an interval of at least 6 hours from each other, apply two coats.

CONDITIONS DURING APPLICATION
In order to avoid the formation of condensation, the surface temperature should be at least 3° C above dew point. During application and curing, the min. ambient temperature must not be lower than 15° C or higher than 30° C; substrate temperature must not be lower than 10° C, since curing is remarkably reduced at lower temperatures.
Application is not advisable when relative humidity exceeds 80%. The term-hygrometric survey should be carried out near the surface to be coated. Make sure there is enough ventilation when application takes place in closed areas.

Recommended thinner 6380, our code 473COL254.
Unit size 0,5 lt.
Colour: Orange.

Veneziani
473COL1192
8014099710100