Boero Bise Two-component Textured Polyurethane Enamel 0,75 Lt 001 White 45100435
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Boero Bise Two-component Textured Polyurethane Enamel. 0,75 Lt. 001 White.
Polyurethane enamel, with a textured finish and satin effect, with maximum resistance to abrasion, yellowing and severe marine atmospheric conditions. Its pasty consistency allows an easy application by roller, obtaining a perfectly uniform orange-peel effect.
PHYSICAL ASPECTS (at 20° C)
Aspect: Satin
Colour: 001 White
Volume solid % 50 ± 2 %
Specific weight: 1,34 ÷ 1,38 g/cm³
Flash point: 39° C
Viscosity: Creamy paste
APPLICATION DETAILS
Mixing ratio by volume: 4:1 with 635.000C
Pot life: 5 h depending on the temperature
Thinner: 696.000 or 697.000
Application Method: Thinner 696.000 or 697.000 (max. 5 %)
Dry film thickness: Standard range of application 100 μ (Recommended 100 μ)
Wet film thickness: Standard range of application 200 μ (Recommended 200 μ)
Theoretical coverage m2/litri.: Range of application at recommended thickness 5
Primers recommended: Delta 3000 – Delta UC HB – Boeroguard
Note: The product is provided in two tins to be mixed entirely and carefully before use. The eventual dilution must be done after mixing the two components. The physical data of two-component products relate to the components after they have been mixed together.
SURFACE PREPARATION
Pressure wash with freshwater and remove all traces of oil and grease. All the surfaces to be painted must be cleaned, dried and free of contaminants. If necessary, sand with grit n. 240/320, blow with clean and dry air to remove any sanding residue, dust or dirt.
Fiberglass: On new surfaces, degrease with SIRIO before proceeding with sanding wih grit n. 240 / 320, blow with clean and dry air to remove any sanding residue, dust or dirt.
APPLICATION CONDITIONS
To avoid the formation of condensation, the temperature of the surface should be at least 3 °C above dew point. During the application and curing the min. ambient temperature should be 10 °C, or higher than 30° C; substrate temperature must not be lower than 5° C since curing is reduced at lower temperatures. Application is not advisable when relative humidity exceeds 80%. The thermo-hygrometric survey should be carried out near the surface to be coated. It is important to be sure there is sufficient ventilation when the application takes place in closed areas.
SAFETY RULES
In order to protect personal health it is advisable to comply with the EU DPR 303 and 547 regulations. Avoid, for example any contact of the product with the skin and eyes. Use in well ventilated areas,in enclosed areas use aspirators, fans and air ventilators. Wear masks, goggles, gloves while applying the product.
NOTE
The applied product must not come in contact with water, chemical products or submitted to mechanical stress before the curing is completed. The wet film thickness is referring to an undiluted product. In case of dilution, this value increases.
