Boero Sentilak Topcoat For Bilges 0,75 Lt 051 Metallic Grey 45100480
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Boero Sentilak Topcoat For Bilges. 0,75 Lt. 051 Metallic Grey.
Glossy topcoat for bilges based on particular resins that confers good chemical resistance, in particular to penetration of humidity, oils, fuel and detergents. This odorless enamel can be applied directly on fibreglass, wood, steel and aluminium, upon preparation. Easy to apply, it has a good coverage power with an excellent levelling.
PHYSICAL ASPECTS (at 20° C)
Aspect: Glossy
Colour: 051 Metallic Grey
Volume solid %: 51%
Specific weight: 1,2 ± 0,02 Kg/Lt
Flash point: 35° C
APPLICATION DETAILS
Thinner: 703 (10 – 20 %)
Application Method
Conventional: Pressure: 3,5 bar Nozzle diameter: 1,4 mm
Airless: Pressure: 150 bar Gun: 0,3 – 0,6 mm (0,012 – 0,024 in) Spray angle : 65° - 80°
Thinner: 703 (5 – 10%)
Dry film thickness: Standard range of application 40 μ (Recommended 40 μ)
Wet film thickness: Standard range of application 80 μ (Recommended 80 μ)
Theoretical coverage m²/L.: Range of application at recommended thickness 12,7
Primers recommended: Anchorprimer – Giano
SURFACE PREPARATION
The product is applied directly on clean surfaces that have been degressed and, if necessary, sanded. For bare wood: Polywood primer should be used on bare wood.
For new GPR, degrease with Sirio, sand and apply it.
For application on old one-component enamel, remove by scraping all materials with poor adhesion.
APPLICATION CONDITIONS
To avoid the formation of condensation, the temperature of the surface should be at least 3 °C above dew point. During the application and curing the min. ambient temperature should be 10 °C, or higher than 30° C; substrate temperature must not be lower than 5° C since curing is reduced at lower temperatures. Application is not advisable when relative humidity exceeds 80%. The thermo-hygrometric survey should be carried out near the surface to be coated. It is important to be sure there is sufficient ventilation when the application takes place in closed area
SAFETY RULES
In order to protect personal health it is advisable to comply with the EU DPR 303 and 547 regulations. Avoid, for example any contact of the product with the skin and eyes. Use in well ventilated areas,in enclosed areas use aspirators, fans and air ventilators. Wear masks, goggles, gloves while applying the product.
NOTE
The applied product must not come in contact with water, chemical products or submitted to mechanical stress before the curing is completed. The wet film thickness is referred to an undiluted product. In case of dilution, this value increases.
