Boero Fresh Water Epoxy Coating For Internal Use 2,5 Lt 001 White 45100505
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Boero Fresh Water Epoxy Coating For Internal Use. 2,5 Lt. 001 White.
Epoxy coating for internal use where there is contact with foodstuff and fresh water. This product complies with 82/711/EEC, 85/572/EEC, 90/128/EEC and 92/39/EEC concerning hygiene in packaging, containers and utensils intended to come in contact with foodstuff.
PHYSICAL ASPECTS (at 20° C)
Aspect: Glossy
Colour: White .001
Volume solid %: 100%
Specific weight: 1,35 ± 0,35 Kg/l
Flash point: 102° C
APPLICATION DETAILS
Mixing ratio by volume: 3:2 in volume, 2:1 in weight
Pot Life: 50 min at 20° C
Thinner: The product must be applied as supplied
Method of Application: Airless: Pressure: 150 bar Nozzle diameter: 0,3 –0,6 mm (0,012 – 0,024 in) Opening angle : 65° - 80°
The product must be applied as supplied
Dry film thickness: Standard range of application 125 - 200 μm (Recommended 150 μm)
Wet film thickness: Standard range of application 125 - 200 μm (Recommended 150 μm)
Theoretical coverage m²/litre: Range of application at recommended thickness 6,7
SURFACE PREPARATION
Steel – Stainless steel: wash at high pressure with fresh water to remove oil and grease contamination (if necessary include washing with specific thinner). All surfaces must be clean, dry and without contamination (if necessary use the Bresle method ISO 8502-6 to check the salinity degree). Verify that the metal presents suitable conditions of "steel preparation" (on welds, edges and various imperfections, the required degree of P 3 + ISO 8501-3). The preparation of the metal should be Sa 2 ½ (ISO 8501-1/3), with a surface profile of between 50 and 80 μm (values of roughness Ry5 or Rz DIN, corresponding to Medium Grade - 85031), using a suitable abrasive. Cover with the product provided for the metal treated in the standard above and before it presents signs of oxidation and/or colour change. Before proceeding with the application of the products provided, blow with clean dry compressed air to remove any abrasive residue and dirt.
APPLICATION CONDITIONS
To avoid the formation of condensation, the temperature of the surface should be at least 3 °C above dew point. During the application and curing the min. ambient temperature should be 10 °C, or higher than 30° C; substrate temperature must not be lower than 5° C since curing is reduced at lower temperatures. Application is not advisable when relative humidity exceeds 80%. The thermo-hygrometric survey should be carried out near the surface to be coated. It is important to ensure there is sufficient ventilation when the application takes place in closed areas.
SAFETY RULES
In order to protect personal health it is advisable to comply with the EU DPR 303 and 547 regulations. Avoid, for example any contact of the product with the skin and eyes. Use in well ventilated areas, in enclosed areas use aspirators, fans and air ventilators. Wear masks, goggles, gloves while applying the product.
