Boero Epolight Win Two-Component High-Build Epoxy Filler 0,75 Lt 001 Light Green 45100510
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Boero Epolight Win Two-Component High-Build Epoxy Filler. 0,75 Lt. 001 Light Green.
Ultra light, high build two-component Epoxy filler, mostly used when it is important to obtain high quality finishing, without increasing the weight of the vessel. Easy to apply in all climates (hot & cold), it gives a high thickness in one coat without the risk of sagging. It is solvent free, does not shrink and is easy to sand. Can be used on any surface.
PHYSICAL ASPECTS (at 20° C)
Aspect: Matt
Colour: Light green
Volume solid %: 100%
Specific weight: 0,50 g/cm³
Flash point: 58° C
Shore hardness scale: After 7 days >= 40
APPLICATION DETAILS
Mixing ratio by volume: 2:1 with 623.000
Pot life: 60 minutes at 20° C
Application Method: Spatula
Dry film thickness: Standard range of application (per coat) Up to 10 mm (Recommended 2 – 8 mm)
Wet film thickness: Standard range of application (per coat) Up to 10 mm (Recommended 2 – 8 mm)
Theoretical coverage litre/m2: Theoretical coverage at recommended thickness 2 – 8 mm
Primers recommended: Delta 3000 – Delta UC HB – Defender
Note: The product is provided in two tins to be mixed entirely and carefully before use. If deemed necessary Epolight Win and Epomar can be mixed together creating an intermediate product improving the hardness of the complete cycle. Mix the two components separately before
mixing together.
SURFACE PREPARATION
After the sanding of Epoxy or Polyurethane primers, apply layers of filler until reaching the desired thickness. Sand between coats, blow with clean and dry compressed air. Cover with Epoxy or Polyurethane products. All filling work must be sanded before coverage to have a good adhesion.
APPLICATION CONDITIONS
To avoid the formation of condensation, the temperature of the surface should be at least 3 °C above dew point. During the application and curing the min. ambient temperature should be 15 °C, or higher than 35° C; substrate temperature must not be lower than 10° C since curing is reduced at lower temperatures. Application is not advisable when relative humidity exceeds 80%. The thermo-hygrometric survey should be carried out near the surface to be coated. It is important to be sure there is sufficient ventilation when the application takes place in confined areas.
SAFETY RULES
In order to protect personal health it is advisable to comply with the EU DPR 303 and 547 regulations. Avoid, for example any contact of the product with the skin and eyes. Use in well ventilated areas,in enclosed areas use aspirators, fans and air ventilators. Wear masks, goggles, gloves while applying the product.
NOTE
STORAGE: Storage: Make sure that the material is always stored at a temperature between 5 °C and 35 °C. Do not expose to direct sunlight. The applied product must not come in contact with water, chemical products or submitted to mechanical stress before the curing is completed.
