International Interfill 830 A + B Epoxy Filler 5 Lt 458COL661
Interfill 830 is the best choice for profiling above and below the waterline of hulls made of steel, aluminum and composite.
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
PRODUCT DESCRIPTION
Interfill 830 is the best choice for profiling above and below the waterline on steel, aluminium and composite hulls. The special 2-component light grey epoxy formulation can fill up to a thickness of 25mm in one coat without the risk of sagging/slumping.
* Low density composition
* High strength and impact resistance
* Easy sanding
* Waterproof
When sanded, the surface of the Interfill 830 is smooth enough to be directly overcoated with Interprime 820 high build epoxy primer. Interprotect or Interprime 880 may also be used. Interfill 830 is particularly suitable for application over large areas.
PRODUCT INFORMATION
Colour: YAA867
Finish: Matt
Specific Gravity 0.75
Volume Solids 100%
Mixing Ratio 1:1 by volume (as supplied)
Mixing ratio by weight: 1.15:1 YAA867: YAA868
Converter/Curing Agent YAA868
Typical Shelf Life: 2 yrs
VOC (As Supplied) 77 g/lt
Unit Size: 5 Lt
DRYING/OVERCOATING INFORMATION
Drying
10°C (50°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Sandable 48 hrs 28 hrs 19 hrs 13 hrs
Pot Life 75 mins 55 mins 45 mins 20 mins
Overcoating
Substrate Temperature
10°C (50°F) 15°C (59°F) 23°C (73°F) 35°C (95°F)
Overcoated By Min Max Min Max Min Max Min Max
Epoxy GP Coating 5 days - 3 days - 2 days - 1 days -
Interfill 833 - - 28 hrs - 19 hrs - 13 hrs -
Interprime 820 5 days - 3 days - 2 days - 1 days -
Interprime 880 5 days - 3 days - 2 days - 1 days -
Interprotect (Professional) 5 days - 3 days - 2 days - 1 day
Note: Once the time for sanding has been exceeded, all fillers should be sanded before overcoating to ensure good adhesion. A sanded filler may be left for a period up to 3 months before being overcoated with further epoxy filler or with Interprime 8-series. After 3 months the filler must then be re -sanded before overcoating. It is recommended that Interfill 830 should be used at temperatures above 10°C/50°F.
If the temperature falls below 10°C/50°F during the curing process, ensure that additional time is allowed before overcoating the product with solvent based epoxy primers.
APPLICATION AND USE
Preparation All substrates must be primed, clean and dry.
PREVIOUSLY PAINTED SURFACES
In Good Condition: Wash with Super Cleaner, rinse with fresh water and allow to dry. Sand with 80-180 grit paper.
In Poor Condition: Remove all previous coatings and prime the substrate.
STEEL/ALUMINIUM: Prime with Intergard 269 or Interprime 820.
BARE/NATURAL WOOD: Prime stable constructions only, with Interprime 820.
GRP: For osmosis treatment follow the Gelshield specification ensuring the Interfill 830 is only used during STAGE 2.
BARE GRP/COMPOSITE: Sand with 80-180 grade (grit) paper.
If left for longer than 24 hours, two component epoxy primers and fillers will need sanding with 80-180 grit paper to ensure a good physical key.
Method: Mix the two components thoroughly to an even colour. Remove any dust from the surface. Apply firmly in a spreading action. When hardened, sand smooth with 80-180 grit wet or dry paper. Interfill 830 may be overcoated with itself or with Interfill 833 as soon as it is cured enough not to be lifted during the screeding process.
Useful Tips: Thinner International GTA220 for equipment cleaning only.
Thinning: Do not thin.
Ventilation and Humidity Control: Avoid conditions of low temperatures coupled with high humidity as this can result in the formation of a surface by-product which will need to be removed by detergent wash followed by fresh water rinse, or by sanding, prior to the application of any subsequent layers.
Other: Spread mix out on a board to avoid excess heat build up and to keep the working life as long as possible. When fairing a hull, two or three 'cross coats' of Interfill 830 will ensure the desired shape is obtained. Where large areas have been faired, sand with a longboard to allow for the curvature of the hull.
Some Important Points: Do not use unless mixed thoroughly with the curing agent at specified ratio. Do not apply more than recommended WFT at any one time. Do not use below 10°C/50°F. Do not thin. Do not wipe down cured filler with thinners/solvents.
Substrate temperature should be minimum 10°C and maximum 35°C. Product temperature should be minimum 10°C and maximum 35°C. Ambient temperature should be minimum 10°C and maximum 35°C.
Compatibility/Substrates: Do not use on traditional wood constructions where the wood will expand and contract through changes in the moisture content. Interfill 830 should be applied over cured epoxy primers or fillers or onto cured GRP/Composite. Interfill 830 may be overcoated with Interfill 833, Interprime 820, Interprime 880 or Interprotect. Gelshield 200 or Gelshield Plus may be used over Interfill 830 within osmosis schemes.
Number of Coats: As required
Coverage/spreading rate: (Theoretical) - 0.2 m²/lt @ 5000 micron (200 mil) Wet film thickness (WFT).
Recommended dry film thickness (DFT) per coat 20000 microns by trowel or palette knife.
Recommended wet film thickness (WFT) per coat 20000 microns wet by trowel or paleltte knife.
Application Methods: Palette knife, trowel
