Veneziani WOOD VB-SHINE AQUA 7W6.322 1L TC water-based Gloss Varnish YM473COL525
Veneziani WOOD VB-SHINE AQUA 7W6.322 Two-component water-based gloss varnish with high resistance to the marine environment for the treatment of internal and external wooden surfaces, .000 Trasparent, 1L.
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Veneziani WOOD VB-SHINE AQUA 7W6.322 Two-Component Water-Based Gloss Varnish
Two-component, water-based, transparent, glossy and non-yellowing polyurethane varnish. Excellent levelling, resistance to abrasion and chemical agents. Easy to apply. Equipped with high resistance to the marine environment, it is particularly suitable for the treatment of internal and external wooden surfaces. Also excellent for wooden floors and piles. Not suitable for substrates subject to continuous immersion.
Application: brush, roller or spray.
TECHNICAL SPECIFICATIONS
Theoretical coverage: 12,0 m2L
Mixing ratio: 5:1
Recoating time: 12h - 36h (20°C)
Hard dry: 12h - 36h
Thinner: water
Finish: Gloss
Colour: Trasparent .000
Solids (by volume): ASTM D2369 44 ± 2%
Specific gravity: UNI EN ISO 2811-1 1,05 ± 0,05 g/cm3
Flash point: UNI EN ISO 13736 N.A.
VOC (calculated average content): ISO 11890-2/2006 40 g/l
Pack: 1 lt
SURFACE PREPARATION
New or renewed wood: The humidity of the wood must not exceed 18%, sand the surface thoroughly with paper n. P120 - P180. Before proceeding with the application of the products provided, blow with clean and dry air to remove any residual sanding and dirt.
Prime with a coat of S-PROTECT AQUA then apply the first coats of VB-SHINE AQUA diluted at 15 - 20%. proceed with the following coats (3 - 5 coats) as it is.
Already painted wood: sand to eliminate traces of paint during stripping or to level the surface; apply 2 - 4 coats of VB-SHINE AQUA as it is.
N.B. Between coats, sand with fine Scotch Brite (gray).
CONDITIONS DURING APPLICATION
In order to avoid the formation of condensation, the temperature of the surface should be at least 3 °C above dew point. During the application and curing the min. ambient temperature must not be lower than 15 °C or higher than 30 °C; the min support temperature must not be lower than 10°C, because the crosslinking is significantly slowed at temperatures below.
Application is not advisable when relative humidity exceeds 75%. The term-hygrometric survey should be carried out near the surface to be coated. Make sure there is enough ventilation when the application takes place in closed areas.
Storage
It is recommended to avoid exposure to air and extreme temperatures. Store the product in a cool place and protect it from frost. To maximize the shelf life in the can, it is good to check that the container is well closed during the storage and the temperature is between 5 °C and
35 °C. Avoid exposure to direct sunlight.
