Veneziani Subcoat XT Filler A+B 2 Kg 473COL204
Epoxy compound, 100% solids by volume which can be applied underwater, providing excellent adhesiontothe support. Particularly useful for temporary repairs of leaks and cracks of the boat, when it is in mooring or sailing.
Visit us in our shop
WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!
In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!
We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.
Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
(modificale nel modulo Rassicurazioni cliente)
Veneziani Subcoat XT Filler A+B 2 Kg
Epoxy compound, 100% solids by volume which can be applied underwater, providing excellent adhesiontothe support. Particularly useful for temporary repairs of leaks and cracks of the boat, when it is in mooring or sailing. It perfectly adheres on fiberglass, Gel coat, already existing epoxy products, epoxy tar as well as steel and concrete. It is suitable for temporary repairs on seacocks, boot topping and submerged parts of cement quays.
Product information
Aspect Matt
ColourLight blue Solidi (in volume)ASTM D2369 100%
Specific gravity UNI EN ISO 2811-1 1,45÷ 1,60g/cm³
Flash point UNI EN ISO 13736 >60°C
VOC(calculated average content) ISO 11890-2/2006 0g/l
SURFACE PREPARATION
Clean the surfaces by using metallic brushesor scrapers to removeany area which is about to detach.APPLICATION PROCEDURE Sub Coat Xt is a two-componentproduct. Mix the two components(white base, blue hardener) manuallywearing protective gloves which must be constantlywetor keeping hands in a bowl of water or in the sea. In order to blend it, start to handle a quantity of hardener(blue paste), then add to it an equal quantity of base product (white paste), then mix with wet hands until you get a homogeneous light blue colour and a uniform consistency. It is possible to perform these operations even underwater without altering thefinal result. Do not add any thinner.Sub Coat Xt has a limited period of applicability. Such time decreases when temperatures are higher than 25°. Apply the product when the surface temperature is above 5°. Apply an averagethickness of4 mm.
Notes
It is recommended to carefully mix the two components before catalysis. Do not add any solvent orfluidifier.
N.B.The drying times and the overcoating intervals increase with higher thickness of the applied film.Always check the existing painting film is perfectly dry before applying a further product coat.
CONDITIONS DURING APPLICATION
The productcan be applied with a water temperature between +5°C and+30°C, since the curing process is considerably slowed at inferior temperatures. It is suggested to apply the product with sea currents higher than 0,8 knots and wave widths higher than 50cm and in any case inpresence of short waves.Make sure that thereis an adequate ventilation when the paint is applied in closed spaces.
Storage
It is recommended to avoid exposure to air and extreme temperatures. To maximizethe shelf life in the can, be surethat the container is well closed during the storage and that temperature is between 10° C and 35° C. Avoid exposure to direct sunlight.
Safety rules
Observe the provisions of DPR 303 and 547. For example,avoid contact with skin, operate in well ventilated areas and, if indoor, use extractors, fans and air conveyors. During the application, use appropriate protections (masks, gloves, glasses, etc). Before using, read section 7-8 of the SDS.
INSTRUCTIONS FOR THE DISPOSAL OF PRODUCTS AND PACKAGING
Empty packaging that contained products: dispose of empty packaging according to the requirements of the waste disposal law, for example by taking them to the recycling center.
Recommended thinner, only for tool cleaning, is 5610, our code COL250.
Unit size 2 kg (A+B).
Colour: Light blue.
