Veneziani Polygoal two-component Undercoat White 153 2.5lt 473COL208
zoom_out_map
chevron_left chevron_right
-15%

Veneziani Polygoal two-component Undercoat White 153 2.5lt 473COL208

Veneziani Polygoal Undercoat. Good expansion. Two-component polyurethane primer for thick coating systems with high performance. Since it is high-build, even one coat is helpful to cover possible micro-porosities of the substrate. White 153. Pack 2.5lt.

€124.64 VAT included

€102.16 VAT excluded

€146.63-15%

Il Nostro Negozio

Visit us in our shop

WE ARE AT YOUR DISPOSAL AT OUR POINT OF SALE
Not just online! Come and visit us also in the shop!

In our store you will find a wide selection of selected items and you will be assisted by our specialized staff with over a decade of experience in the nautical sector.
Everything for the boat ... deck equipment, anchoring and mooring, hydraulic and electrical systems, photovoltaics, stainless steel hardware, antifouling and paints, engine spare parts, on-board safety, sailing accessories, nautical instruments, GPS, depth sounders and much more!

We are in San Giorgio di Nogaro in the province of Udine, an important basin, located in the Bassa Friulana, bathed by the Corno river ... a few km from well-known destinations such as Lignano, Grado, Trieste etc.

Nautimarket Europe s.r.l., Via Marittima 17, 33058 San Giorgio di Nogaro (UD) Italy

Politiche per la sicurezza
(modificale nel modulo Rassicurazioni cliente)
Politiche per le spedizioni
(modificale nel modulo Rassicurazioni cliente)
Politiche per i resi
(modificale nel modulo Rassicurazioni cliente)

Veneziani Polygoal two-component Undercoat White 153 2.5Lt

Polyacrilic bi-component undercoat with thickness for paint cycles with high performances. Good sandpaper quality, particularly suitable as undercoat for finishes. The height thickness allows to close the micro porosity of the existing cycle. Mainly applicable on bottoms of epoxy plasters before sandpaper. Applicable on fiberglass and gelcoat after accurate sandpapering and cleaning. Polygoal is an excellent foundation coat for polyutherane finishing, giving relevance to the brilliance.

Product information
Finish Matt
Colour White .153
Solids (by volume) ASTM D2369    60 ± 2%
Specific weight UNI EN ISO 2811-1   1,40 g/cm³
Flash point UNI EN ISO 13736   23 – 55 °C
VOC (calculated average content) ISO 11890-2/2006  360 g/l

Application and use
SURFACE PREPARATION

It is recommended to apply POLYGOAL on surfaces with already treated supports with well cross-linked products and seasoned. Sandpaper with abrasive paper grit 220-240. The support must be cleaned, dry and correctly prepared. Before performing the painting, verify that all surfaces must be perfectly dry, cleaned, free of oils, grease and other contaminants agents.

CONDITIONS DURING APPLICATION
In order to avoid the formation of condensation, the surface temperature should be at least 3° C above dew point. During the application and curing, the min. ambient temperature must not be lower than 15° C or higher than 30° C.; substrate temperature must not be lower than 10°C, since curing time is remarkably reduced at lower temperatures.
Application is not advisable when relative humidity exceeds 80%. The term-hygrometric survey should be carried out near the surface to be coated. Make sure there is enough ventilation when the application takes place in closed areas.



Recommended thinner 5780, our code 473COL252.
Colour: White 153.

473COL208 Unit size  0,75Lt
473COL2081 Unit size 2,5Lt

Choose
desidered size from the drop down menu.

Veneziani
473COL2081
8025223433468